- The IPH
Defects like folds can arise using forging for the production of long flat pieces made of aluminium. A special defect is the formation of inner folds. These can be seen in the grain flow. Inner folds have a negative effect on the dynamic properties of the forged part. As a production process, forging can be divided into single-directional and multi-directional forging. The formation of inner folds was observed at the single-directional forging. By using the multi-directional forging, a forming operation working from different directions, the forming can be set variably. Thus the development of folds can be prevented. A newly developed method can help in the selection of the forming process and in determining an appropriate tool geometry. Here especially the area is adapted, where the development of inner folds occur. Therefore a calculation model was developed. It integrates a computer-aided identification of the inner folds. Using this model, a correction of the parametrically constructed forging tool is possible.
multidirectional-forging, long flat pieces, aluminium, fibre orientation
To be able to meet the challenges of globalization, the optimization of internal transport is becoming increasingly important. Due to the further development, drones are an innovative material handling technology. The use of drones can be cost-efficient, especially for time-critical transport tasks. However, drones are characterized by a very low payload and very high operating costs. Therefore drones are in some cases more economical than conventional means of transport, but they do not offer an universal solution for all internal transport tasks.
drones, intralogistics, transport, transport systems, economic efficiency
The service life of rolling contacts is dependent on many factors. The choice of materials in particular has a major influence on when, for example, a ball bearing mayfail.Within an exemplary process chain for the production of hybrid high-performance components through tailored forming, hybrid solid components made of at least two different steel alloys are investigated. The aim is to create parts that have improved properties compared to monolithic parts of the same geometry. In orderto achievethis, several materials are joined prior to a forming operation. In this work, hybrid shafts created by either plasma(PTA)orlaser metal deposition (LMD-W) welding are formed via cross-wedge rolling(CWR)to investigate the resulting thickness of the material deposited in the area of the bearing seat. Additionally,finite element analysis (FEA)simulations of the CWRprocessare compared with experimental CWR results to validate the coating thickness estimation done via simulation. This allows for more accurate predictionsofthe cladding materialgeometry after CWR,and the desired welding seam geometrycan be selected by calculating the cladding thicknessvia CWR simulation.
Cross-Wedge Rolling, Forming, hybrid, tailored forming
To manufacture semi-finished hybrid workpieces with tailored properties, a finite element simulation assisted process chain design was investigated. This includes the process steps of cross wedge rolling, hot geometry inspection, induction hardening, and fatigue testing. The process chain allows the utilisation of material combinations such as high-strength steels with low-cost and easy to process steels. Here, plasma transferred arc welding is applied to supply the process chain with hybrid specimen featuring different steel grades. An overview of the numerical approaches to consider the various physical phenomena in each of the process steps is presented. The properties of the component behaviour were investigated via the finite element method (FEM) and theoretical approaches.
Cross-Wedge Rolling, Forming, hybrid, tailored forming
In this work we present an application of the virtual element method (VEM) to a forming process of hybrid metallic structures by cross-wedge rolling. The modeling of that process is embedded in a thermomechanical framework undergoing large deformations. Since forming processes include mostly huge displacements within a plastic regime, the difficulty of an accurate numerical treatment arises. VEM illustrates a stable, robust and quadratic convergence rate under extreme loading conditions in many fields of numerical mechanics. Numerically, the forming process is achieved by assigning time-dependent boundary conditions instead of modeling the contact mechanics yielding to a simplified formulation. Based on the two metallic combinations of steel and aluminum, different material properties are considered in the simulations. The purpose of this contribution is to illustrate the effectiveness of such a non-contact macroscopic framework by employing suitable boundary conditions within a virtual element scheme. A comparison with the classical finite element method (FEM) is performed to demonstrate the efficiency of the chosen approach. The numerical examples proposed in this work stem out from the DFG Collaborative Research Centre (CRC) 1153 “Process chain for the production of hybrid high-performance components through tailored forming”.
simulation, FEM, bulk metal forming, tailiored forming
Handling hot steel parts weighing several kilos is physically demanding. A new type of forging tongs is designed to reduce stress at work, prevent pain and reduce sick leave.
forging, ergonomic, stress reduction
The selection of storage, commissioning and transport systems (sct systems) is very complex due to the large number of available systems on the market and influencing factors. One important influencing factor is automation. To classify the degrees of automation of sct systems and to determine the individually required automation a method is proposed below.
automation, storage, commissioning and transport systems
Upfront investment costs for the tooling of injection molds are the basis for deciding if a mold is tooled and hence if a part is viable for mass-production. If tooling costs are too high, a product may not viable for production. If tooling costs are estimated too low by the tool shop, contract implications may arise.
The goal of this research is to develop a method with humanlike quotation accuracy, achieve standardization, factor in historic quotation data and shorten quotation process times. The machine learning approach developed is based on geometry data of parts and additional meta-information.
injection molding, tooling, industry 4.0
The aim of subproject B1 of the Collaborative Research Center (CRC) 1153 is to determine the formability of novel hybrid semi-finished products by means of incremental forming cross wedge rolling. Main aspect is the forming of hybrid semi-finished products made of steel, aluminium and hard material alloys. In order to reduce the component weight, the use of hybrid semi-finished products makes it possible to manufacture less stressed segments of a previously monolithic component from a light metal. To increase wear resistance, a component area (e.g. a bearing seat) can be coated with a hard material. In addition, process variables (e.g. temperature and force) are to be measured in contact between work piece and tool in the future. There are primarily two material arrangements for the semi-finished products used: coated (coaxial - demonstrator shaft 1) and joined at the front (serial - demonstrator shaft 3). One challenge is the heating of the semi-finished products necessary for forming, since the hybrid semi-finished product has different flow resistances due to the different materials and may have to be heated inhomogeneously in order to enable uniform forming.
cross-wedge rolling, forming, hybrid work pieces, tailored forming, hybrid semi-finished products
Quality assurance methods are a central success factor for the further industrialization of additive manufacturing. This paper presents an approach for an optical inspection system that controls the quality of additive material extrusion layer by layer. The inspection task gets analyzed, hardware components for data acquisition are designed and a first step towards texture-analytical detection of defects is presented.
additive manufacturing, 3d printing, material extrusion, fused deposition modeling, image processing
To this day, the design of preforms for hot forging processes is still a manual trial and error process and therefore time consuming. Furthermore, its quality vastly depends on the engineer’s experience. At the same time, the preform is the most influencing stage for the final forging result. To overcome the dependency on the engineer’s experience and time-consuming optimization processes this paper presents and evaluates a preform optimization by an algorithm for cross wedge rolled preforms. This algorithm takes the mass distribution of the final part, the preform volume, the shape complexity, the appearance of folds in the final part and the occurring amount of flash into account. This forms a multi-criteria optimization problem resulting in large search spaces. Therefore, an evolutionary algorithm is introduced. The developed algorithm is tested with the help of a connecting rod to estimate the influence of the algorithm parameters. It is found that the developed algorithm is capable of creating a suitable preform for the given criteria in less than a minute. Furthermore, two of the five given algorithm parameters, the selection pressure und the population size, have significant influence on the optimization duration and quality.
preform optimization, genetic algorithm, cross wedge rolled, adaptive flash
A product-dependent, individual process development represents a main cost driver in laser material processing. Therefore, the expert system SmQL is being developed in an FQS-funded project, in which process knowledge can be stored in a formalized form and represented in rule form. This is intended to minimize times for setup processes and secure knowledge in the company in the long term.
expert system, industry 4.0, laser materials processing
The Hybrid Forging Process satisfies the needs of modern structural and material lightweight engineering by combining forming and mechanical joining operations within one process. This paper presents an analytical approach for the prediction of symmetrical joining bonds of bulk material and sheet metal. Finite element simulations verify that the analytical approach provides a threshold value for the sheet metal thickness at which the bending elongation is reduced significantly. Furthermore, the analytical approach emphasizes that surpassing the threshold value leads to a saturation of the bending elongation reduction and only marginal benefit is achieved by increasing the sheet metal thickness.
hybrid forging, bonding, joining, elastomechanics, lightweight, multi-material manufacturing
Material transports in production facilities are subject to constant change. Production batch sizes are becoming smaller and a trend towards batch size 1 is becoming apparent. For this reason, a new research project is examining drones respectively unmanned aerial vehicles (UAV) as so far rarely used transport technology for possible applications in intralogistics. Barriers to use UAV and risks during its use are categorized and evaluated. In the following, requirements for the operating environment and the technical equipment itself are derived from this. Overall, it is investigated to what extent UAV can be integrated into the operational infrastructure of companies in certain use cases and whether the resulting change in logistics performance justifies its use cost-effectively.
drones, material transport, requirements, economic efficiency
Components manufactured by hybrid forging in progressive dies have a high potential for lightweight construction. The example of a suspension arm shows the advantage of hybrid forged parts creating new possibilities for structural and material lightweight construction. Additionally, it is demonstrated that the heat subjected to hybrid forged parts during the subsequent hardening process does not threaten the potential of material lightweight construction.
progressive compound, hybrid, forging
Driverless transport systems are a building block for more efficient production systems in intralogistics, but have weaknesses in human-machine interaction. In a complex research project, a voice-based assignment is being developed, among other things, which is intended to make human-machine interaction more intuitive and increase its acceptance.
automated guided vehicle, augmented reality, smart glasses, voice control
Belt conveyor systems are an excellent way of conveying bulk material. With increasing load and transport distance, these systems become larger and energy efficiency becomes an important factor. Rollers are an integral part of belt conveyor systems. The running behaviour of idlers during operation has an impact on the energy efficiency of the entire system. The development of driven idlers is seen as one way to reduce the energy consumption of belt conveyor systems. This contribution shows that the investigation of conventional and driven idlers under different conditions is necessary and that a test rig for the investigation of these idlers has been developed at the Institut für Integrierte Produktion Hannover.
idlers, rollers, driven idler, bulk material handling
The Collaborative Research Centre 1153 (CRC 1153) “Process chain for the production of hybrid high-performance components through tailored forming” aims to develop new process chains for the production of hybrid bulk components using joined semi-finished workpieces. The subproject B1 investigates the formability of hybrid parts using cross-wedge rolling. This study investigates the reduction of the coating thickness of coaxially arranged semi-finished hybrid parts through cross-wedge rolling. The investigated parts are made of two steels (1.0460 and 1.4718) via laser cladding with hot-wire. The rolling process is designed by finite element (FE)-simulations and later experimentally investigated. Research priorities include investigations of the difference in the coating thickness of the laser cladded 1.4718 before and after cross-wedge rolling depending on the wedge angle, cross-section reduction, and the forming speed. Also, the simulations and the experimental trials are compared to verify the possibility of predicting the thickness via finite element analysis (FEA). The main finding was the ability to describe the forming behavior of coaxially arranged hybrid parts at a cross-section reduction of 20% using FEA. For a cross-section reduction of 70% the results showed a larger deviation between simulation and experimental trials. The deviations were between 0.8% and 26.2%.
cross-wedge rolling, hybrid forming, FEA, coating thickness
Within the Collaborative Research Centre (CRC) 1153 “Tailored Forming “the manufacturing of hybrid bulk components is investigated. Therefore, a process chain consisting of joining, forming, milling and quality control has been established by multiple subprojects.Within subproject B1 of the CRC forming of hybrid parts by the incrementally forming cross-wedge rolling (CWR) process is investigated. The superior aim is to determine process limits and capabilities, when forming parts consisting of different materials joined by varying technologies.
In this paper, the investigation of cross-wedge rolling of serially arranged hybrid parts made of steel and aluminum is described. The focus of the research presented in this publication is the displacement of the joining zone of hybrid parts due to the cross-wedge rolling process. Therefore, finite element simulations have been developed, that allow the investigations of hybrid solid components. After simulation of various variations of the cross-wedge rolling process, i.e. differently shaped tools and forming velocities, experimental trials were carried out with identical parameter sets. A comparison of simulation and experiment, showed that the simulation model is capable of describing the cross-wedge rolling process of hybrid parts. The standard deviation of the displacement of the joining zone between simulation and experimental trials is 8.8% with regard to all investigated cases.
tailored forming, cross-wedge rolling, material forming, aluminum, steel
Within the Collaborative Research Centre 1153 “Tailored Forming“ a process chain for the manufacturing of hybrid high performance components is developed. Exemplary process steps consist of deposit welding of high performance steel on low-cost steel, pre-shaping by cross-wedge rolling and finishing by milling.
Hard material coatings such as Stellite 6 or Delcrome 253 are used as wear or corrosion protection coatings in industrial applications. Scientists of the Institute of Material Science welded these hard material alloys onto a base material, in this case C22.8, to create a hybrid workpiece. Scientists of the Institut für Integrierte Produktion Hannover have shown that these hybrid workpieces can be formed without defects (e.g. detachment of the coating) by cross-wedge rolling. After forming, the properties of the coatings are retained or in some cases even improved (e.g. the transition zone between base material and coating). By adjustments in the welding process, it was possible to apply the 100Cr6 rolling bearing steel, as of now declared as non-weldable, on the low-cost steel C22.8. 100Cr6 was formed afterwards in its hybrid bonding state with C22.8 by cross-wedge rolling, thus a component-integrated bearing seat was produced. Even after welding and forming, the rolling bearing steel coating could still be quench-hardened to a hardness of over 60 HRC. This paper shows the potential of forming hybrid billets to tailored parts. Since industrially available standard materials can be used for hard material coatings by this approach, even though they are not weldable by conventional methods, it is not necessary to use expensive, for welding designed materials to implement a hybrid component concept.
tailored forming, cross-wedge rolling, hard material coatings, PTA
Within the Collaborative Research Centre (CRC) 1153 Tailored Forming a process chain for the manufacturing of hybrid high performance components is developed. Exemplary process steps consist of deposit welding of high-performance steel onto low cost steel and pre-shaping the component by cross-wedge rolling (CWR), supported by an optical quality control system. A combination of a fringe projection profilometry setup with a thermal imaging camera is used to monitor the components before and after the CWR process. Both geometry and thermal imaging data are combined, assigning temperature values to 3D data points.
In this paper, the acquisition of combined temperature-geometry data is described. The data before and after the CWR is compared to the input and the result data of the forming simulation that was used to design the CWR process. The comparison shows the quality and sustainability of the heating process as well as the influence of the transportation of the hot component prior to forming. Additionally, the accuracy of the used simulation model and software are evaluated by data examination. The examination shows the limits of idealised and simplified assumptions for the simulation, e.g., a homogeneous temperature distribution before forming or the modelling of the heat transfer on contact surfaces.
tailored forming, cross-wedge rolling, material forming, aluminum, steel, optical measurement
Student job, Master thesis, Bachelor thesis, Project thesis, Internship